|
|
|
 |
 |
 |
 |
|
|
|||
| Description: | Super Therm is a unique combination of high-performance
aliphatic urethanes, elastromeric acrylics, standard acrylics and resin
additives in a water-borne formula. No co-solvents are present and
will dry by evaporation. Due to the unique combination of acrylics
and urethanes, Super Therm cures out completely in 14 days to an extremely
tough, durable, non-yellowing, water-resistance coating that also provides
flexibility, water-proofing, and UV stability. Super Therm was built
to meet the requirements of industrial uses which needed a tough surface
and flexibility against the stresses of contraction and expansion.
Also, unlike all other "reflective" coatings on the market which
offer only a single reflective ceramic to provide heat reflection, Super
Therm is designed with four separate ceramics (two are reflective, one
acts as a dead air space, and the 4th blocks 99.5% of infrared
radiation). This allows Super Therm to be an actual
"insulating" coating not just a reflective coating. The
urethane resin acts to bind all the other resins and ceramics together and
provides a vapor barrier in the dry film similar the paper backing on batt
insulation. Super Therm's design is based on the latest ceramic
technology know in the science field today with continuing research and
testing to keep it the best insulating coating in the world market.
|
Other Products SUPER THERM |
|
| Application Methods: | Surfaces must be clean and dry before application.
Loose, flaking old paints or corrosion must be removed from the surface
before applying. High pressure water-blasting is as effective as
light sandblasting in removing loose or flaking surfaces. As a rule,
"a coating is only as good as the surface it covers."
Grease, oil, waxy substances, dirt, etc. must be cleaned from the
surface. Old paint can remain if bonded solidly to surfaces.
Super Therm can bond to metal, masonry, wood and other porous surface
substrates and can be applied by airless or air pot spray, roller and by
brush. If rolling, it may take two coats to apply required
mils. Spraying requires a steel carbon tip of sizes 0.028 - 0.032
(remove all filters from spray equipment before using). Roller is
best applied by a 3/4 inch nap roller. Do not apply very thick on a
single coat. if thickness is desired, apply in multiple coats.
A Thick coat will allow the top coating surface to dry before the bottom,
creating cracks in the coating. If applied when humidity is high or
it rains constantly for 3-4 days after Super Therm is applied, you may
notice some bubbling effects on the coating. DO NOT PUNCTURE these
bubbles. This is normal as the formula is water-based and is
absorbing the moisture and therefore forming bubbles (never apply if
raining or chance of rain the day of application). When the rain
quits, the sun will dry out the coating and allow it to cure down
naturally. As the moisture is drawn out by the sun, they bubbles
will settle down and allow the coating to adhere in its normal dry down
without problem.
|
Application Examples |
|
| Features: |
68% solids by vol. / 63.6% by wgt.
16 wet mil coat / 9-10 dry mil coat Dry Time: 1 hour-touch, 2 hours-recoat, 14-21 days full cure Spread: 100 sq.ft./gal. = 10 dry mils / Viscosity: 105-110 KU Flame Spread Test: ASTM E-84-89 UL 723 / Flame: 0 / Smoke: 0 Contains silver citrate to protect against mold, mildew & other pathogens. Elongation: 125% / Hail-resistant to cracking Flexibility: 180 bend test - ASTM D1737 1/8" mandrels Weathering: 10 years / UV / Weathering - 2000 hours US Consumer product Safety Commission - Approved U.S.D.A. - Approved for use around foods VOC (Volatile Organic Compounds) is 67 grams / liter pH: 8.9 - 9.0 / Density: 11.88 lbs. / gallon Salt Spray Corrosion Test: ASTM B117 450 hrs evaluation. ASTM D1654 over black steel; Rating procedure b:9 Sound Deadening is the function of blocking sound waves which is identical to blocking heat waves. Separate testing was performed in association with UNC & Stoughton Trailer; both registered 68% sound reduction. BTU Conduction Stoppage. BTU heat flow of cold steel metal is 367.20 through the metal. of one thin layer of Super Therm at 0.01 thickness is 3.99 BTU through the coating. This is the coating film alone. K value is 0.1; R Value is 10 w/o the reflectivity factor to give a total of R19.
|
||
| Important: |
Do not take internally. Avoid contact with eyes. If solution
does come in contact with eyes, flush immediately with water and contact a
physician for medical advice. Avoid prolonged contact with skin or
breathing of spray mist. For quickest removal from skin, wash with
water before drying. KEEP OUT OF REACH OF CHILDREN.
|
||
| Limited Warranty: |
Unless Superior Products provides a written warranty of fitness for a
particular use, Superior Product's sole warranty is that the product, as
supplied, will meet then current sales specifications and is specific only
to one year. Customer's exclusive remedy and Superior's sole liability
for breach of warranty is limited to refund of the purchase price or
replacement of any product shown to be other than as warranted and Superior
Products expressly disclaims any liability for incidental or consequential
damages.
|
||
| Coverage Recommendations (must be applied by a certified applicator for roofs): |
Urethane Foam Roofing / Metal Roofing
|
90 sq. ft. / Gal
|
|
|
Membrane Roofing
|
100 sq. ft. / Gal
|
||
|
Concrete (prime w/ Inner Seal @ 150 sq. ft. / gal / 3 coats
or Super Base / HS @ 100 sq. ft. / gal.)
|
100 sq. ft. / Gal
|
||
| Interior/Exterior Vertical Walls | 100 sq. ft. / Gal | ||
|
Hi-Tek Coatings, Corp. - 298 Central Ave. - Hawthorne, NJ 07506 Phone: (973) 423-1514 Fax: (201) 652-1361 Email: abunagan@hi-tekcoatings.com |
